Reagents
TMT buffer:
0.19 M Tris-HCl (pH 7.4-7.6)
12 mM MgCl2
0.2 % Triton X-100
SMase solution:
SMase from Streptomyces sp. @ 2 units/ml in 10 mM Tris-HCl (pH 7.4-7.6)
Lipid Extraction
1) Following the appropriate time of treatment, transfer 4.5 ml into each of two duplicate glass pyrex tubes and maintain on ice.
2) Spin down cells in the table top centrifuge at 1,200 rpm, 40C, for 5 minutes.
3) Gently aspirate and discard the spent media (remember, consider it radioactive). Be extremely careful not to disturb the pellet since it is somewhat dispersed.
4) Immediately upon aspirating each tube, add 3 mls of chloroform-methanol, 1:2, and vortex vigorously!!
--> It is necessary to add the C:M immediately in order to get good dispersion of the pellet. If too much time passes prior to resuspension, the pellet does not dissolve well and sonication is necessary.
--> This is a good point to stop by storing the samples in the -200C freezer.
5) Add 0.8 ml of water and vortex vigorously.
--> Still have a monophase and it may be best to allow this monophase to equilibrate for a little while.
6) Spin out all large debris by spinning at 3,000 rpm for 5 mins.
7) Transfer the supernatant to a new pyrex glass tube and vortex again. Do not transfer any of the pellet, even if it is necessary to sacrifice some of the sample.
8) Add 1 ml of chloroform to break phases and vortex vigorously.
9) Add 1 ml of water and again vortex vigorously.
10) Spin samples at 3,000 rpm for 5 mins. to completely separate phases.
11) Aspirate off the top phase and the interface.
--> Remove enough such that no aqueous material remains at the meniscus.
12) The lower phase should constitute ~2 ml. Transfer 1.5-1.7 ml of this to a new pyrex glass tube.
--> This is a good point to stop by storing the transferred samples in the -200C freezer.
SMase assay
13) Dry down samples completely.
14) Resuspend dried lipids in 50 µl TMT buffer.
15) Vortex vigorously and sonicate via three 1 minute bursts, vortex and rest for 1 minute in between.
16) Pre-incubate tubes in 37°C water bath for 5 minutes.
17) Add 50 µl of SMase solution to each reaction tube and allow reaction to proceed for 30 minutes.
--> Remember to have a control tube containing no enzyme to determine background.
18) Add 1.5 ml Chloroform/Methanol (2:1) to each tube to stop reactions.
19) Vortex vigorously and add 0.2 ml water to complete the Folch extraction.
20) Vortex tubes and spin down for 5 minutes at 1,000Xg (break on low).
21) Collect ~400 µl of the upper phase into previously prepared plastic scintillation vials and count samples.
HL6的磷脂定量Post-choline标记
2010-05-26 22:56:49 来源：不详 评论：0 点击：
ReagentsTMT buffer:0.19 M Tris-HCl (pH 7.4-7.6)12 mM MgCl20.2 % Triton X-100SMase solution:SMase from Streptomyces sp.
分享到：
收藏
收藏
评论排行
- ·中国发酵企业数据库(4)
- ·(4)
- ·CoQ10高产菌株选育的研究进展(2)
- ·抗生素发酵工艺所用冷却塔的性能分析及处理(1)
- ·微生物菌种选育技术.rar(1)
- ·发酵生产染菌及其防治(1)
- ·赤藓糖醇发酵工艺研究(1)
- ·重组AiiA 蛋白可溶性表达及发酵条件优化(1)
- ·生物反应器设计软件_发酵罐绿色版(1)
- ·酵母粉、酵母浸粉的区别(1)
- ·雷帕霉素研究进展(1)
- ·透明质酸用途和行业概况(1)
- ·黄酒制作工艺(1)
- ·水解(酸化)工艺与厌氧发酵的区别(1)
- ·糖蜜酒精废液处理过程中产生的微生物蛋...(1)
- ·紫杉醇高产菌发酵产物的分离、纯化和鉴定(1)
